Cisco Systems WSC4500XF16SFP User Manual Page 49
- Page / 194
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
1-25
Catalyst 4500 Series Switches Installation Guide
78-14409-08
Chapter 1 Product Overview
Supervisor Engines
Gigabit Ethernet Uplink Ports
The Gigabit Ethernet uplink ports operate in full-duplex mode only. GBICs have
SC connectors to interface with multimode fiber (MMF) and single-mode fiber
(SMF) cable. For more information about GBICs, refer to the Catalyst 4500
Series Module Installation Guide.
When two Supervisor Engine Vs are present in a Catalyst 4507R and Catalyst
4510R, all four uplinks are active on both Primary (active) and Secondary
(standby) supervisor engines by default, or two uplinks will be active in a
nonredundant configuration. This limits access to slot 10 on the Catalyst 4510R
to ports 3 and 4 only. You can only use the 2-port Gigabit Ethernet switching
module (WS-X4302-GB) or the Access Gateway Module (WS-X4604-GWY) in
slot 10 (flex-slot), when a Supervisor Engine V is used.
10-Gigabit Ethernet Uplink Ports
The 10-Gigabit Ethernet uplink ports operate in full-duplex mode only, and are
only on the WS-X4516-10GE and WS-X4013+10GE. These ports use the
hot-swappable 10GBASE X2 optical transceivers. The X2s have SC connectors to
interface with multimode fiber (MMF) and single-mode fiber (SMF) cable.
On a Catalyst 4510R with a Supervisor Engine V-10GE, the user has the option to
use either four Gigabit Ethernet uplinks using SFPs or two 10-Gigabit Ethernet
uplinks using X2s. The user also has the option of using the Gigabit Ethernet and
10-Gigabit Ethernet uplinks simultaneously. With this option, the tenth slot can
only support the WS-X4302-GB switching module. On a Catalyst 4507R, the user
can use the Gigabit Ethernet uplinks and 10-Gigabit Ethernet uplinks
simultaneously.
When two Supervisor Engine V-10GEs are present in a Catalyst 4510R or Catalyst
4507R switch, or two Supervisor Engine II-Plus 10GEs are present in a Catalyst
4507R, one X2 uplink is active on both the primary (active) and secondary
(standby) supervisor engines by default, or two uplinks will be active in a
nonredundant configuration.
- Installation Guide 1
- Copyright © 2002 3
- CONTENTS 5
- Contents 6
- 5 Troubleshooting 5-1 8
- A Specifications A-1 8
- B Repacking a Switch B-1 8
- Audience 9
- Organization 9
- Related Documentation 10
- Conventions 11
- Waarschuwing 13
- Varoitus 13
- Attention 14
- Avvertenza 14
- Advarsel 15
- ¡Advertencia! 15
- Varning! 16
- Obtaining Documentation 17
- Product Documentation DVD 18
- Ordering Documentation 18
- Documentation Feedback 19
- • 1 877 228-7302 20
- • 1 408 525-6532 20
- Submitting a Service Request 21
- Product Overview 25
- Catalyst 4503 Switch Features 26
- Switch Features 27
- Catalyst 4506 Switch Features 30
- Supervisor Engines 42
- • CONSOLE Port, page 1-26 48
- • RESET Button, page 1-26 48
- Gigabit Ethernet Uplink Ports 49
- SFP Ports 50
- 10/100BASE-T Port 50
- CONSOLE Port 50
- RESET Button 50
- Fan Assembly 51
- Power Supplies 55
- AC input 2 receptacle 56
- AC input 1 receptacle 56
- AC input 1 on switch 56
- AC input 2 on switch 56
- Power Supply LEDs 58
- Power Supply Fan 59
- Load-Sharing Feature 59
- Table 1-8 Input Modes 60
- (2450 W Max Output Power) 61
- (1400 W Max Output Power) 61
- System Architecture 64
- Power over Ethernet 65
- PoE Over-subscription 66
- PoE Line Cards 66
- Management Flow 69
- Switching Traffic Flow 70
- Over-subscription 71
- Supervisor Redundancy 72
- Preparing for Installation 73
- Electrostatic Discharge 74
- Calculating DC Input Current 85
- Ventilation 86
- Components 87
- Site-Planning Checklist 88
- Statement 1006 94
- Rack-Mounting the Switch 100
- 78-14409-08 100
- Grounding 108
- Parts and Required Tools 112
- Grounding lug 114
- Screws (M4) 114
- Removing and Replacing FRUs 117
- Statement 1034 118
- Required Tools 121
- Captive screws 122
- Statement 1019 124
- Power switch 125
- Removal Procedure 127
- Statement 1046 129
- Installation Procedure 132
- Captive installation 135
- Fan assembly 135
- Removing the Fan Assembly 139
- Installing the Fan Assembly 139
- Verifying the Installation 140
- Mux buffers 142
- Clock module 142
- Good Bad 145
- Verify the New Modules 146
- Troubleshooting 147
- System Boot Verification 148
- WS-X4148-RJ 157
- 10/100 B 157
- Serial Numbers 163
- SN: AAANNNNXXXX 164
- 113784, 781-00251-01A0 166
- Specifications 167
- Environmental 168
- Switching Components 168
- Physical Characteristics 168
- Redundancy 169
- Table A-10 Input Modes 181
- Supplies in Combined Mode 181
- Repacking a Switch 185
- Numerics 187
- A-10, A-13 193
- A-5, A-6 193
© 2020, manymanuals.com. All rights reserved. | 1.434 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals