Cisco Systems 2691 User Manual

Quick Start GuideCisco 2691 Modular RoutersINCLUDING LICENSE AND WARRANTY1 Cisco 90-Day Limited Hardware Warranty Terms2 Documents, Equipment, and Too

10The brackets for Cisco 2691 routers are shown in Figure 1.Note The slots in the brackets marked RIGHT are for securing cables with cable ties.Figure

11Figure 3 Bracket Installation for Center Mounting with Rear Panel ForwardFigure 4 Bracket Installation for Front MountingFigure 5 Bracket Installati

12Installing on DesktopCaution If you place the Cisco router on a desktop, do not place anything that weighs more than 10 pounds (4.5 kilograms) on to

134 Connect CablesWarningDo not work on the system, or connect or disconnect cables during periods of lightning activity. Statement 1001System Manage

14Caution If you connect dual DC power sources, both sources must be the same polarity. Do not connect a –DC with a +DC source to a Cisco 2691 router.

15WarningThe illustration shows the DC power supply terminal block. Wire the DC power supply as illustrated. The proper wiring sequence is ground to g

16WAN, LAN, and Voice ConnectionsThe connections and cables listed here are described in detail in the following documents:• Cisco 2600 Series Hardwar

175 Power Up the RouterChecklist for Power-UpYou are ready to power up the Cisco router after the following steps are completed:• Chassis is securely

18You may see different startup messages:• If you see the following messages, the router has booted with a configuration file and is ready for initial

19Initial Configuration Using Cisco Router and Security Device ManagerIf the following messages appear at the end of the startup sequence, Cisco Route

21 Cisco 90-Day Limited Hardware Warranty TermsThere are special terms applicable to your hardware warranty and various services that you can use dur

20Step 3 Enter a host name for the router (this example uses 2691):Configuring global parameters:Enter host name [Router]: 2691Step 4 Enter an enable

21Step 11 The configuration is displayed:The following configuration command script was created:hostname 2691enable secret 5 $1$D5P6$PYx41/lQIASK.HcSb

22For interface numbering information, see the “Interface Numbering” section on page 22.Step 1 To proceed with manual configuration using the CLI, ent

23• A WIC in each WIC slot (containing interfaces Serial 0/0 and Serial 0/1 in physical slot W0, interface Serial 0/2 in physical slot W1, and interfa

24To access documentation on Cisco.com:For Cisco 2600 series platform documentation, start on Cisco.com at http://www.cisco.com, and select Products &

2510 Documentation FeedbackYou can send comments about technical documentation to [email protected] can submit comments by using the response car

26Definitions of Service Request SeverityTo ensure that all service requests are reported in a standard format, Cisco has established severity definit

27

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

32 Documents, Equipment, and ToolsUser DocumentationAll the documents referenced in this quick start guide are available online on Cisco.com. To be s

4Warning DefinitionWarningIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before

5AvvertenzaIMPORTANTI ISTRUZIONI SULLA SICUREZZAQuesto simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone

6AvisoINSTRUÇÕES IMPORTANTES DE SEGURANÇAEste símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais.

7AdvarselVIGTIGE SIKKERHEDSANVISNINGERDette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du be

8WarningThis unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special

9WarningTo avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contai