Cisco Systems ASR1002 Quick Start Guide

QUICK START GUIDECisco ASR 1002 Router1 Documentation and Resources2 Prepare for Installation3 Rack-Mount the Router4 Connect the Router to the Networ

10Figure 6 Cisco ASR 1002 Router Ground Connector Location and eUSB Panel DoorStep 1 Use the wire stripper to strip one end of the AWG #6 wire approxi

11Step 5 Locate the chassis ground connector on the side of your chassis. Step 6 Insert the two screws through the holes in the grounding lug.Step 7 U

12Figure 8 Cisco ASR 1002 Integrated Route Processor Console and Auxiliary Port ConnectorsStep 3 After you establish normal router operation, you can

13Step 3 Configure to a fixed speed through the command-line interface (CLI) commands.Connect the Shared Port Adapter CablesThe instructions for conne

14Proceed to the “Start the System” section on page 14 to complete the installation.5 Start the SystemBefore you start the system, you must connect p

15Figure 11 AC Power Supply for the Cisco ASR 1002 RouterTable 1 describes the AC power supply LEDs on the Cisco ASR 1002 Router.Table 1 Cisco ASR 100

16Figure 12 shows the DC power supply for the Cisco ASR 1002 Router.Figure 12 DC Power Supply for the Cisco ASR 1002 RouterTable 2 describes the DC po

17Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. Typically, green or green/

18Step 9 Connect the ground, positive, and negative leads to the power source.Step 10 Turn the branch source breaker on.Step 11 Turn the power supply

19Step 1 Turn on power. The green OK LED on the power supply turns on. (Both power supplies are required in the Cisco ASR 1002 Router.)Step 2 Listen f

21 Documentation and ResourcesDocumentation for the Cisco 1000 Series Aggregation Services Routers documentation is online with the exception of the

20Table 4 provides information about the Cisco ASR1000-ESP5 LEDs in the Cisco ASR 1002 Router as the system starts.Table 4 Cisco ASR1000-ESP5 and ASR1

21%IOSXEBOOT-4-DEBUG_CONF: (rp/0): Using DEBUG_CONF file /misc/scratch/debug.confFeb 13 13:00:38.546 R0/0: %PMAN-3-PROCFAIL_IGNORE: All process failur

22*Feb 13 13:01:28.701: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down*Feb 13 13:01:29.728: %LINEPROTO-5-UPDOWN:

23Router> enableStep 3 At the password prompt, enter your system password. If an enable password has not been set on your system, this step may be

24for management of the system, extended setup will ask youto configure each interface on the system Would you like to enter basic management setup? [

25no ip address!interface GigabitEthernet0/0/1shutdownno ip address!interface GigabitEthernet0/0/2shutdownno ip address!interface GigabitEthernet0/0/3

26 Enter your selection [2]:Router#reloadProceed with reload? [confirm] *Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reaso

27Use, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - Re

28Save the Running Configuration to NVRAM To store the configuration or changes to your startup configuration in NVRAM, use the copy running-config st

29Power Off the Cisco ASR 1002 RouterThis section explains how to shut down the Cisco ASR 1002 Router. It is recommended that before turning off all p

32 Prepare for InstallationThis section contains information about tools and parts, warnings, site preparation information, and information for rack-

30Step 2 Using the handles on both sides of the module, with two hands, gently insert the Cisco ESP5 or -ESP10 into the top chassis slot. Note Handle

31Step 9 Power on the router by turning the power switch to the on (I) position.Replace a Power Supply in the Cisco ASR 1002 RouterThis section provid

32Figure 14 Cisco ASR 1002 Router AC Power Cord b. Take the power cord and run it below the handles of the power supply in slot 1 (the power supply yo

33Note Using a tie wrap for the AC power cable is optional and not necessary. However, if you do attach the AC power cable to a power supply tab and t

34Step 7 Replace the DC power supply within five minutes or the system will shutdown.You have completed the procedure for removing a DC power supply f

35Figure 18 Cisco ASR 1002 Router DC Power Supply Step 5 Insert the stripped end of the ground lead all the way into the ground lead receptacle on the

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0

4Prepare for Rack-Mount InstallationBefore you begin the rack-mounting tasks:• Decide whether or not you want to front-mount or rear-mount the chassis

5Attach the Rack-Mount Brackets—Chassis Rear-MountedTo install the rack-mount on a Cisco ASR 1002 Router for a rear rack-mount configuration, follow t

6Figure 3 shows the Cisco ASR 1002 Router in a four-post rack.Figure 3 Installing the Cisco ASR 1002 Router in a Four-Post Rack - Front and Rear Rack-

7Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make certain that you use the rack-mount bracket ear ho

8Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and component damage.Step 1

9Figure 5 Attaching the Cable-Management Bracket to the Cisco ASR 1002 RouterStep 3 Using the bottom rack-mount ear hole, insert the screw through cab