Cisco Systems IOS XR User Manual Page 23
- Page / 282
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Implementing BGP on Cisco IOS XR Software
Information About Implementing BGP on Cisco IOS XR Software
RC-7
Cisco IOS XR Routing Configuration Guide
• Commands entered at the session group level define address family-independent commands (the
same commands as in the neighbor submode).
• Commands entered at the address family group level define address family-dependent commands
for a specified address family (the same commands as in the neighbor-address family configuration
submode).
• Commands entered at the neighbor group level define address family-independent commands and
address family-dependent commands for each address family (the same as all available neighbor
commands), and define the use command for the address family group and session group commands.
Template Inheritance Rules
In Cisco IOS XR software, BGP neighbors or groups inherit configuration from other configuration
groups.
For address family-independent configurations:
• Neighbors can inherit from session groups and neighbor groups.
• Neighbor groups can inherit from session groups and other neighbor groups.
• Session groups can inherit from other session groups.
• If a neighbor uses a session group and a neighbor group, the configurations in the session group are
preferred over the global address family configurations in the neighbor group.
For address family-dependent configurations:
• Address family groups can inherit from other address family groups.
• Neighbor groups can inherit from address family groups and other neighbor groups.
• Neighbors can inherit from address family groups and neighbor groups.
Configuration group inheritance rules are numbered in order of precedence as follows:
1. If the item is configured directly on the neighbor, that value is used. In the example that follows, the
advertisement interval is configured both on the neighbor group and neighbor configuration and the
advertisement interval being used is from the neighbor configuration:
RP/0/RP0/CPU0:router(config)# router /jointfilesconvert/86220/bgp 140
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp)# neighbor-group AS_1
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp-nbrgrp)# advertisement-interval 15
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp-nbrgrp)# exit
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp)# neighbor 10.1.1.1
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp-nbr)# remote-as 1
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp-nbr)# use neighbor-group AS_1
RP/0/RP0/CPU0:router(config-/jointfilesconvert/86220/bgp-nbr)# advertisement-interval 20
The following output from the show /jointfilesconvert/86220/bgp neighbors command shows that the advertisement interval
used is 20 seconds:
RP/0/RP0/CPU0:router# show /jointfilesconvert/86220/bgp neighbors 10.1.1.1
BGP neighbor is 10.1.1.1, remote AS 1, local AS 140, external link
Remote router ID 0.0.0.0
BGP state = Idle
Last read 00:00:00, hold time is 180, keepalive interval is 60 seconds
Received 0 messages, 0 notifications, 0 in queue
Sent 0 messages, 0 notifications, 0 in queue
Minimum time between advertisement runs is 20 seconds
For Address Family: IPv4 Unicast
BGP neighbor version 0
- Text Part Number: OL-5554-05 1
- CONTENTS 3
- Contents 10
- Preface 11
- Obtaining Documentation 12
- Documentation Feedback 13
- Submitting a Service Request 15
- BGP Functional Overview 18
- BGP Router Identifier 19
- BGP Default Limits 19
- BGP Configuration 20
- Neighbor Submode 21
- Configuration Templates 22
- Template Inheritance Rules 23
- Template Inheritance 27
- No Default Address Family 31
- Routing Policy Enforcement 32
- Update Groups 34
- BGP Best Path Algorithm 34
- Comparing Pairs of Paths 35
- Order of Comparisons 36
- Multiprotocol BGP 37
- Route Dampening 39
- BGP Route Reflectors 40
- Enabling BGP Routing 44
- Logging Neighbor Changes 50
- Adjusting BGP Timers 50
- Configuring BGP Weights 54
- Configuring a BGP Neighbor 74
- Disabling a BGP Neighbor 85
- Monitoring BGP Update Groups 91
- BGP Confederation: Example 94
- IS-IS Functional Overview 101
- IS-IS Configuration Grouping 101
- IS-IS Interfaces 102
- Multitopology Configuration 102
- Limit LSP Flooding 102
- Single-Topology IPv6 Support 103
- Nonstop Forwarding 104
- Multitopology IPv6 Support 104
- Multi-Instance IS-IS 105
- Overload Bit on Router 105
- Default Routes 106
- Multicast-Intact Feature 106
- Prerequisites 107
- DETAILED STEPS 108
- Restrictions 109
- SUMMARY STEPS 110
- Example: 113
- Example:: 117
- Prerequisite 126
- Summary Steps 134
- Customizing Routes for IS-IS 135
- Software 138
- Where to Go Next 140
- Additional References 140
- Technical Assistance 141
- OSPF Functional Overview 145
- OSPF Routing Components 148
- Backbone Area 149
- Stub Area 149
- Not-so-Stubby Area (NSSA) 149
- OSPF Process and Router ID 150
- Supported OSPF Network Types 151
- Authentication Strategies 152
- Key Rollover 152
- Default Route for OSPF 153
- Route Redistribution for OSPF 155
- Graceful Restart for OSPFv3 157
- Restart Mode 158
- Enabling OSPF 161
- Examples 180
- address mask 185
- Enabling Graceful Restart 198
- ABR 1 Configuration 207
- ABR 2 Configuration 207
- Cisco IOS XR Software 211
- Overview of RIB 212
- RIB Administrative Distance 213
- RIB Support for IPv4 and IPv6 213
- How to Deploy and Monitor RIB 214
- Routing Policy Language 222
- Named Set Form 224
- Inline Set Form 224
- Named Form 225
- Inline Form 226
- Routing Policy Language Usage 227
- Set community based on MED 228
- Policy Definitions 229
- Parameterization 230
- Boolean Operator Precedence 231
- When Attributes Are Modified 232
- Default Drop Disposition 233
- Control Flow 233
- Policy Verification 234
- Policy Statements 235
- Disposition 236
- Boolean Conditions 238
- Attach Points 239
- BGP Policy Attach Points 240
- Dampening 241
- Default Originate 241
- Neighbor Export 242
- Neighbor Import 242
- Redistribute 243
- Show bgp 244
- Table Policy 245
- BGP Attributes and Operators 245
- OSPF Policy Attach Points 247
- OSPFv3 Policy Attach Points 248
- IS-IS Policy Attach Points 250
- Attached Policy Modification 251
- Defining a Route Policy 253
- policy-name 256
- Directly Connected Routes 265
- Recursive Static Routes 265
- Floating Static Routes 266
- Configuring a Static Route 266
- Configuration Examples 271
Related products and manuals for Networking Cisco Systems IOS XR
Networking Cisco Systems C892FSPK9 User Manual
(144 pages)
(144 pages)
Networking Cisco Systems D200 User Manual
(86 pages)
(86 pages)
Networking Cisco Systems C819GUK9 User Manual
(196 pages)
(196 pages)
Networking Cisco Systems IE 3000 User Manual
(32 pages)
(32 pages)
Networking Cisco Systems CCNA 2 User's Guide
(239 pages)
(239 pages)
Networking Cisco Systems 901 User Manual
(68 pages)
(68 pages)
Networking Cisco Systems OL-16066-01 User Manual
(268 pages)
(268 pages)
Networking Cisco Systems 3620 User Manual
(12 pages)
(12 pages)
Networking Cisco Systems SFS 7024 User Manual
(104 pages)
(104 pages)
Networking Cisco Systems C2960XSTACK User Manual
(112 pages)
(112 pages)
© 2020, manymanuals.com. All rights reserved. | 1.421 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals