Cisco Systems 3000 Instruction Manual Page 174
- Page / 234
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
9-20
Cisco TelePresence System 3000
OL-14521-01
Chapter 9 First-Time Setup
Setting Up CTS Components
c. Press OK until the group number setting changes to 100.
d. Press the Down Arrow key until the No. setting changes to 4.
e. Press the Left Arrow key until the Data setting changes to 0.
f. Press the ON-OFF key to end the service menu.
Step 6 Center the projector display within the screen by completing the following steps:
a. Locate the lock switch and two dials on the side of the projector.
b. Move the switch to the unlock position.
c. Rotate the vertical dial to position the top of the image 1 inch below the bottom of the wood surface.
d. Rotate the horizontal dial to position the sides of the image 15 inches from each of the seams on the
table segments.
Completing this step should center the image in the screen. If the image is not centered, adjust the
image until the distance is equal from each table segment seam.
e. Move the switch to the lock position.
Step 7 Aim the remote control at the lens of the projector.
Tip You can use the screen to reflect the signal back to the projector if you are sitting at the table.
Leave the projector in this state. When the video signal is turned off or disconnected, the projector will
go black for 30 seconds. Then it will count down for 5 minutes and then turn off the lamp.
If a video signal is applied during this 5 minute and 30 second countdown the video will reappear
immediately. If the countdown completes, the projector goes into a cooldown mode which will ignore a
video signal for 30 seconds. It will then stay in a standby mode and will power back up when a video
signal is connected. It will take 15 seconds for the projector to light back up.
Step 8 To check either VGA or document camera input, perform the following steps:
a. Click Presentation Devices on the Hardware Setup window.
b. Perform one of the following steps to test the video input:
• Click the VGA radio button to test input from a VGA device
• Click the Document camera radio button to test input from the document camera
If the input image is displaying correctly, you should see an image projected on the projection surface.
Step 9 If the image is out of focus or is too small, use the projector focus ring to focus the image and use the
zoom lever to create the largest possible image.
Step 10 Click Stop in Cisco TelePresence System Administration to remove the test pattern and complete the
projector test.
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- CONTENTS 3
- Contents 4
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Assembly Overview 13
- Conventions and Terminology 14
- Tools and Equipment List 15
- Tools and Equipment List 16
- Building the Display Assembly 17
- Figure 2-1 Leveling feet 18
- Figure 2-2 Codec Safety trays 19
- 18 - 22” (45.7 cm - 55.8 cm) 26
- Leveling Alignment Points 30
- Leveling Goals 31
- Apply the Black Buffer strips 36
- Figure 4-8 Light Cup bracket 47
- Figure 4-15 Four L-brackets 54
- Accessory Cabinet 65
- CTS3K-FUR-MAPLE 67
- Figure 5-3 Left Display shelf 68
- Figure 5-6 Accessory Cabinet 71
- Figure 5-8 Left Display shelf 73
- Figure 5-11 Accessory Cabinet 76
- Building the Table Assembly 77
- Miscellaneous Table Items 78
- Figure 4 Right Table segment 84
- Figure 5 Right-most Table Leg 85
- Figure 6 Center Table segment 86
- Figure 8 Left Table segment 88
- Figure 10 Left-most Table leg 90
- Attach the table door 91
- Figure 13 Accessory cabinets 93
- 22 23 24 97
- Figure 19 Right Table segment 99
- OL-14521-01 100
- Figure 23 Left Table segment 103
- Figure 25 left Most Table Leg 105
- Figure 26 Microphone Assembly 106
- Figure 28 Accessory cabinets 108
- Elements 109
- Projector Assembly 110
- Privacy Panel Assembly 110
- Codec Assembly 110
- Parts List 111
- Camera Target Assembly 112
- Switch Bracket 112
- Figure 7-1 Camera Assembly 113
- Figure 7-5 Projector Assembly 117
- Figure 7-6 Projector Assembly 118
- Figure 7-7 VGA Module 119
- Figure 7-12 Codec Assembly 124
- Figure 7-13 Codec Assembly 125
- Figure 7-14 Codec Assembly 126
- Figure 7-17 Speaker Assembly 129
- Figure 7-18 Speaker Assembly 130
- Figure 7-19 Speaker Assembly 131
- Parts List 135
- Table Leg Power 140
- Projector Power 140
- Table Leg Signal 141
- IP Phone Signal 141
- Microphone Signal 141
- Projector Signal 141
- VGA Peripheral 141
- Projector HD Video to Codec 142
- Microphones 144
- RJ45 Power over Ethernet 149
- HDMI connector 149
- First-Time Setup 155
- Figure 9-1 Bootup Completed 156
- Figure 9-2 System IP Address 157
- Setting Up CTS Components 158
- Setting Up the Displays 159
- Troubleshooting Displays 160
- Cisco TelePresence 3000/3200 160
- Setting Up the Cameras 161
- Up/down screw 162
- Left/right screws 162
- Rotation screws 162
- Setting Up CTS Components 163
- Show All Camera Targets 164
- Flipping the Video Image 164
- Focus the Camera 164
- Troubleshooting Cameras 166
- Setting Up the Speakers 167
- Setting Up the Microphones 167
- Troubleshooting Microphones 168
- Setting Up the Projector 169
- Other Devices 176
- Maintaining the Projector 178
- Powering Off the System 180
- Removing the Camera Cluster 180
- Uncrating and unpacking: 181
- Removing Audio Components 182
- Removing a Display Shelf 183
- Replacement Bulbs 192
- Replacing a Light Fixture 192
- CTS-AV-EXP 193
- CTS-PRJTR-BL-GEN1 195
- CTS-LIGHT-CTRL 199
- Replacing a Display Shelf 199
- Replacing a Display Shelf 200
- Replacing a Table Top Section 201
- Section Assemblies 205
- Assemblies 217
- 69-1835-01, CTS3K-M 229
- Equipment 231
- Australia 232
- Central Europe 232
- India, UAE, South Africa 232
- North America 233
- Switzerland 234
- United Kingdom 234
Related products and manuals for Unknown Cisco Systems 3000
Unknown Cisco Systems 3750 User Manual
(176 pages)
(176 pages)
Unknown Cisco Systems R4.1.x User Manual
(8 pages)
(8 pages)
Unknown Cisco Systems OL-4266-08 User Manual
(124 pages)
(124 pages)
Unknown Cisco Systems MDS 9100 User Manual
(70 pages)
(70 pages)
© 2020, manymanuals.com. All rights reserved. | 0.635 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals