Cisco Systems 3000 Instruction Manual Page 180
- Page / 234
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
11-2
Cisco TelePresence System 3000
OL-14521-01
Chapter 11 Field-Replaceable Unit Guide
Replacing the Camera Cluster—Part Number CTS3K-CAM-CLST-G2
• The Release Notes for Cisco TelePresence System for your software release
• Power screwdriver with 2.5, 3, and 6 mm (standard or round) Allen bits, or standard 2.5, 3, and 6 mm
Allen wrenches
• 0.9mm Allen wrench for camera lens adjustments (if the lens uses a thumbscrew, no tools are
required)
• Manual screwdrivers, Phillips and flat head types
• Metric wrenches, 10 to 15 mm
• Masking tape
• Laptop computer attached to network
Powering Off the System
Power off the system by turning the power switches to the Off position on the two left PDUs, single right
PDU and, if present, the PDU or auxiliary control unit behind the center display assembly.
Caution Make sure all system power is turned off before beginning this disassembly.
Removing the Camera Cluster
Note Make sure to retain all screws, brackets, and other parts during the disassembly.
Caution Take care not to scratch or mar the display screen during the replacement procedure.
Note The directions left and right refer to the assembly as you face it.
Step 1 Remove the top camera hood by removing the screws that secure it to the bracket.
Step 2 Remove the lens hood by removing the two screws on the bottom of the hood.
Step 3 At the back of the camera cluster, disconnect the six cables: one Ethernet and one signal cable from each
of the three camera processors. As you remove each cable, attach a strip of temporary masking tape and
mark as “left,” “right,” or “center” for identification.
Tip To enable easier access to the loose cables, temporarily attach them to the upper back of the
display with masking tape.
Step 4 Remove the camera assembly by removing the screws from the top and side flanges of the camera
assembly support bracket. Retain the screws and set the assembly aside.
Step 5 Attach the new camera assembly to the mounting bracket using the same M8 screws that were removed.
See Chapter 7, “Assembling the Remaining Cisco TelePresence Elements,” for more information.
- Assembly Guide 1
- Use & Care Guide 1
- Field-Replaceable Unit Guide 1
- CONTENTS 3
- Contents 4
- Introduction 9
- Conventions 9
- Guidelines 10
- Related Documentation 10
- Overview 11
- Chapter 1 Overview 12
- Chapter Organization 12
- Assembly Overview 13
- Conventions and Terminology 14
- Tools and Equipment List 15
- Tools and Equipment List 16
- Building the Display Assembly 17
- Figure 2-1 Leveling feet 18
- Figure 2-2 Codec Safety trays 19
- 18 - 22” (45.7 cm - 55.8 cm) 26
- Leveling Alignment Points 30
- Leveling Goals 31
- Apply the Black Buffer strips 36
- Figure 4-8 Light Cup bracket 47
- Figure 4-15 Four L-brackets 54
- Accessory Cabinet 65
- CTS3K-FUR-MAPLE 67
- Figure 5-3 Left Display shelf 68
- Figure 5-6 Accessory Cabinet 71
- Figure 5-8 Left Display shelf 73
- Figure 5-11 Accessory Cabinet 76
- Building the Table Assembly 77
- Miscellaneous Table Items 78
- Figure 4 Right Table segment 84
- Figure 5 Right-most Table Leg 85
- Figure 6 Center Table segment 86
- Figure 8 Left Table segment 88
- Figure 10 Left-most Table leg 90
- Attach the table door 91
- Figure 13 Accessory cabinets 93
- 22 23 24 97
- Figure 19 Right Table segment 99
- OL-14521-01 100
- Figure 23 Left Table segment 103
- Figure 25 left Most Table Leg 105
- Figure 26 Microphone Assembly 106
- Figure 28 Accessory cabinets 108
- Elements 109
- Projector Assembly 110
- Privacy Panel Assembly 110
- Codec Assembly 110
- Parts List 111
- Camera Target Assembly 112
- Switch Bracket 112
- Figure 7-1 Camera Assembly 113
- Figure 7-5 Projector Assembly 117
- Figure 7-6 Projector Assembly 118
- Figure 7-7 VGA Module 119
- Figure 7-12 Codec Assembly 124
- Figure 7-13 Codec Assembly 125
- Figure 7-14 Codec Assembly 126
- Figure 7-17 Speaker Assembly 129
- Figure 7-18 Speaker Assembly 130
- Figure 7-19 Speaker Assembly 131
- Parts List 135
- Table Leg Power 140
- Projector Power 140
- Table Leg Signal 141
- IP Phone Signal 141
- Microphone Signal 141
- Projector Signal 141
- VGA Peripheral 141
- Projector HD Video to Codec 142
- Microphones 144
- RJ45 Power over Ethernet 149
- HDMI connector 149
- First-Time Setup 155
- Figure 9-1 Bootup Completed 156
- Figure 9-2 System IP Address 157
- Setting Up CTS Components 158
- Setting Up the Displays 159
- Troubleshooting Displays 160
- Cisco TelePresence 3000/3200 160
- Setting Up the Cameras 161
- Up/down screw 162
- Left/right screws 162
- Rotation screws 162
- Setting Up CTS Components 163
- Show All Camera Targets 164
- Flipping the Video Image 164
- Focus the Camera 164
- Troubleshooting Cameras 166
- Setting Up the Speakers 167
- Setting Up the Microphones 167
- Troubleshooting Microphones 168
- Setting Up the Projector 169
- Other Devices 176
- Maintaining the Projector 178
- Powering Off the System 180
- Removing the Camera Cluster 180
- Uncrating and unpacking: 181
- Removing Audio Components 182
- Removing a Display Shelf 183
- Replacement Bulbs 192
- Replacing a Light Fixture 192
- CTS-AV-EXP 193
- CTS-PRJTR-BL-GEN1 195
- CTS-LIGHT-CTRL 199
- Replacing a Display Shelf 199
- Replacing a Display Shelf 200
- Replacing a Table Top Section 201
- Section Assemblies 205
- Assemblies 217
- 69-1835-01, CTS3K-M 229
- Equipment 231
- Australia 232
- Central Europe 232
- India, UAE, South Africa 232
- North America 233
- Switzerland 234
- United Kingdom 234
Related products and manuals for Unknown Cisco Systems 3000
Unknown Cisco Systems 3750 User Manual
(176 pages)
(176 pages)
Unknown Cisco Systems R4.1.x User Manual
(8 pages)
(8 pages)
Unknown Cisco Systems OL-4266-08 User Manual
(124 pages)
(124 pages)
Unknown Cisco Systems MDS 9100 User Manual
(70 pages)
(70 pages)
© 2020, manymanuals.com. All rights reserved. | 2.007 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals